From Wiki Knowledge Base | Teltonika SAS
Main Page > SAS Personal Trackers > GH5200 > GH5200 Configuration > GH5200 Features settings
|This feature is used to prevent the driver from exceeding fixed speed and inspects the driver if needed. When vehicle speed exceeds maximum configured speed value the scenario is activated, and a record is generated. Scenario is activated until speed value decreases below the set parameter value.
This function can only be triggered by the configured button. When the alarm is triggered, an event with IO ID 236 is generated. Eventually an SMS will be sent informing user about the event. A call possibility is also available if desired number is selected near Call to parameter. In addition, users are allowed to configure event priority. Two options are available - Call where voice call comes first and Record where data transmission to servers will be prioritized over a voice call.
User ID feature allows users to send custom number as AVL ID 854 parameter.
This feature gets current accelerometer data and calculates angle between offset positions. Currently there are two positions: horizontal (when the device is in horizontal position and LEDs are on top of the case) and vertical (when the device is in a vertical position and USB connector is facing down). Scanning is performed each second. When calculated angle exceeds configured threshold for configured timeout, then an event with IO ID 242 is generated. SMS event and/or call takes place, if it is configured.
This feature allows users to customize GH5200 volume based on their needs. 3 volume control settings are available - Indication volume, Normal Speaker Volume, Loud Speaker Volume.
The purpose of this function is to notify any alarm events by sending an SMS message to up to 5 receivers and to call up to 5 pre-defined numbers.
These high priority events can be configured:
- Movement Event.
At least one of the following has to be selected for this feature to work - Alarm, ManDown or Movement Event. In addition, at least one SMS Number or one Call Number has to be configured.
Users are allowed to configure SMS sending method. Two options are available - GPRS or SMS option which sends an SMS when GPRS fails and GPRS and SMS option which sends an SMS when GPRS fails or device sends records to the server.
Call Answer Timeout is used for indicating successful call - if voice call was answered but configured time-out has not been reached, the voice call is considered unsuccessful and if only one number is configured, the device repeats the call as many times as the value configured in Call Repeat field. However, if the call is not successful and there are other predefined numbers selected, the device continues to call other configured numbers instead of repeating voice calls to the same number.
NOTE! Some operators provide voice information when the recipient is unreachable or call is not accepted. Such voice information may last longer than the configured time. In that case, the call will be considered as accepted.
Movement Event scenario makes an eventual high priority record (and sends an optional SMS) when the device is stationary or in motion (depending on configured "Mode") for set Timeout.
Timeout is a configured amount of time (in seconds) after which an eventual high priority record is generated.
Movement Event mode generates a record after the start of movement whereas No Movement Event generates a record after the stop of movement.
NOTE! In case if No Movement Event is selected as Mode, then Pre Alarm Timeout is counted additionally.
When enabled, device waits for instant movement/stop detection, then waits for its own Timeout, generates a high priority eventual record and sends it.
Bluetooth Home Zone settings
||Bluetooth Home Zone can be tested on HomeZone scenario FW 55.00.08.Rev.319 or newer
Important Home Zone parameters in Bluetooth features section:
- BLE Geofence – Select to use
ELA BLE advertiser Sensors,
- Home Zone RSSI (dBm) – Lowest Home Zone RSSI threshold before an alarm event.
Example: If Home Zone RSSI (dBm) is set to -100 and the device signal becomes worse (e.x.-101) an alarm event is generated.
- Time-Without-Beacon(s) – Time without beacon detection before violation (minimum 40 seconds)
Example: If Beacon has not been detected by the device for 60 seconds, an alarm event is generated.
Pre-Alarm: Defines how much time user has before record will be send to the server. During this time Alarm event could be disarmed.
Note: This setting also controls Proximity Pre-Alarm.
RSSI (dBm): Defines lowest RSSI signal level for BLE advertising device.
On Exit – Generates an event after device has left the zone.
On Entrance – Generates an event after device has entered the zone.
On Both – Generates an event when device has left and entered the zone.
Call to: Select a number from 10 GSM Predefined Numbers list to which alarm call will be made.
Send SMS To: Select a number from 10 GSM Predefined Numbers list to which SMS will be send.
SMS Text: Defines SMS text that will be send when Home Zone event is generated.
Instructions on how to configure Bluetooth Home Zone functionality can be found in here.
||Amber Alert can be tested on FW 55.00.10.Rev.01 or newer
Instructions on how to configure Amber Alert functionality can be found in here.
Important Amber Alert parameters in Bluetooth features section:
Timeout: Defines time until Amber Alert alarm is processed.
Pre-Alarm: Sets the remaining time, when the pre-alarm should be triggered.
Order Priority: Defines call or record priority.
Call is selected, device will call to defined number and creates Amber Alert record.
Record is selected, device will create Amber Alert record and calls to defined number.
Initial call number: Select a number from 10 GSM Predefined Numbers list to which alarm call will be made.
Alarm call number: Select a number from 10 GSM Predefined Numbers list to which alarm call will be made.
Send SMS To:Selects number from 10 GSM Predefined Numbers list to which Amber Alert SMS will be send.
SMS Text:Defines SMS text that will be send when Amber Alert event will be generated.
Information about proximity configuration can be found in Bluetooth feature section.
Last Known Position
||Last Known Position can be tested on FW 55.00.10.Rev.01 or newer
This feature adds low priority record
AVL ID 386 to all records.
The record shows how much time in seconds has passed since last GNSS fix.
This feature affects Alarm, ManDown, Movement event and Amber Alert features.
If the last good coordinate at the time the record is created is older than 60 seconds, then the new high priority record
AVL ID 69 will be sent immediately after GNSS fix appears. No matter how many different records have been created when there was no GNSS fix, only one high priority
AVL ID 69 record will be created when GNSS fix appears.